BAG 20

 

You need: well-shape stiff natural/mixed fabric; fusing, lining, decorative cord, cardboard.

 

IF THE PATTERNS HAVE DOUBLE CONTOUR, THE SEAM ALLOWANCE IS PROVIDED,

IF THE PATTERNS HAVE SINGLE CONTOUR, THE SEAM ALLOWANCE IS NOT PROVIDED.

 

Sam allowances: 1 cm for all seams.

 

ATTENTION! Before sewing, print paper patterns and lay them out according to the linen width (from 90 to 150 cm) to find out how much material you need (do not forget about double and symmetric details).

 

WHEN SEWING, BE CAREFUL WITH NOTCHES – THEY MUST BE COINCIDING!

 

CUTTING:

 

Fabric:

1. Upper part – 1 piece

2. Bottom – 1 piece

 

Lining:

1. Upper part – 1 piece

2. Bottom – 1 piece

 

Fusing: all fabric/lining details.

 

INSTRUCTIONS:

 

1. Apply the fusing to wring side of fabric/lining details.

 

2. Cut cardboard bottom without seam allowances.

 

3. Stitch upper part as a ring.

 

4. Stitch lining detail as a ring leaving a hole for turning the bag right side out.

 

5. Cut a handle of 40 cm length and 4 cm width. Fold it along the center wrong side out, fold edge allowances under and make a stitch at 0.1 from the edge.

 

6. Set loops as marked (outer detail).

 

7. Stitch lining upper part to upper part inserting the handle.

 

8. Fold upper part inside as marked. Make two parallel stitches around to create a coulisse. Upper stitch goes along loop’s upper edge, lower one goes along lower edge.

 

9. Stitch the bottom to the bag. Stitch lining bottom to the lining.

 

10.Insert cardboard bottom into the bag fixing it with 2-3 stitches to lining bottom.

 

11. Turn the bag right side out through the hole. Stitch the hole.

 

12. Cut the cord into two equal parts. Set one of cords into the loop and, pull it through the coulisse and pull out from this loop. Do the same with another cord and another loop. Set tips on cord ends or tie them.

 

 

 

5699 COMBINED JACKET

 

See details for work with faux fur/leather at How to use the CD.

 

You need: faux fur, faux leather; lining, fusing, 1 separable zip, 4 spring hooks, 4 rings for spring hooks, 1 clasp.

 

IF THE PATTERNS HAVE DOUBLE CONTOUR, THE SEAM ALLOWANCE IS PROVIDED,

IF THE PATTERNS HAVE SINGLE CONTOUR, THE SEAM ALLOWANCE IS NOT PROVIDED.

 

Seam allowances: 1 cm for all seams.

 

ATTENTION! Before sewing, print paper patterns and lay them out according to the linen width (from 90 to 150 cm) to find out how much material you need (do not forget about double and symmetric details).

 

WHEN SEWING, BE CAREFUL WITH NOTCHES – THEY MUST BE COINCIDING!

 

CUTTING:

 

Faux fur:

1. Back sleeve – 2 pieces

2. Front sleeve – 2 pieces

3. Back part – 1 piece

4. Front part – 2 pieces

5. Collar – 1 piece

 

Faux leather:

1. Back placket – 2 pieces

2. Front lower placket – 4 pieces

3. Front right placket – 1 piece

4. Front right placket _inner – 1 piece

5. Front left placket – 2 pieces

6. Collar – 1 piece

7. Cuff – 2 pieces

8. Waistband – 1 piece

9. Half-belt – 16 pieces

10. Belt loop – 1 piece

 

Lining:

1. Back sleeve – 2 pieces

2. Front sleeve – 2 pieces

3. Back part – 1 piece

4. Front part – 2 pieces

 

Fusing:

1. Back placket – 1 piece

2. Front lower placket – 2 pieces

3. Front right placket – 1 piece

4. Front left placket – 1 piece

5. Cuff – 2 pieces

 

NB: please try faux-leather details of unneeded material before you double them of the fur.

 

INSTRUCTIONS:

 

1. Apply the fusing to wrong side of faux leather.

 

2. Lay half-belts right sides together and overstitch them along 3 edges. Cut allowances close to the seam. Turn half-belts right sides together, pres them and topstitch at 0.1 cm along seam line.

 

3. Press right placket along fold line. Lay right plackets (inner and outer) right sides together inserting the zipper (zipper teeth look opposite the edge). Stitch plackets together stitching zipper right edge in. Fold inner placket out adjusting long edges and making patch placket. Topstitch allowances on outer placket. Lay left plackets right sides together, insert zipper’s left edge and stitch plackets together. Overstitch plackets along upper/lower edges. Fold details into right side and topstitch along 3 edges at 0.1 cm and 0.7 cm.

 

4. Pull each half-belt into spring hook at 3 cm length and topstitch them. Do the same for half-belts and rings. Pin half-belts with spring hooks to right placket, pin half-belts with rings to left one. Zip the zipper, clasp spring hooks to rings and adjust half-belts’ length. Stitch half-belts’ open edges to plackets’ open edges. Unzip the garment and process plackets as 2 details.

 

5. Stitch upper front darts.

 

6. Stitch front sleeve to front part. Stitch back sleeve to back part.

 

7. Stitch shoulder edges with sleeve upper edges.

 

8. Stitch sleeve lower edge and side edge with one seam.

 

9. Press a cuff along the center right side out. Lay the cuff flat, fold it wrong side out and stitch it as a ring. Turn the cuff right side out, press the seam. Stitch the cuff to sleeve hem.

 

10. Fold belt loop in 3 layers, then stitch. Cut the loop into 2 pieces.

 

11. Stitch front lower plackets to back lower placket. Press seams apart. Sew belt loops’ lower edges to outer plackets’ side seams as marked. Fix loops’ upper edge to plackets’ upper edges.

 

12. Make a seam with loose stitches along jacket hem, gather the hem a little. Stitch plackets’ outer parts to jacket hem.

 

13. Stitch the lining in the same way as fur details leaving a hole into left sleeve’s lower seam for turning the garment right side out. Stitch the lining to lower placket’s inner parts.

 

14. Stitch outer collar into jacket’s neckline. Stitch inner collar into lining neckline. Press seams apart.

 

15. Lay the lining and the jacket right sides together, insert front plackets and overstitch front edging/collar/hem.

 

Overstitch the hem with the lining. Turn the jacket right side out through a hole in the sleeve. Stitch the hole.

 

16. Make decorative stitch along the seam joining lower plackets and front/back parts as well as along the hem.

 

17. Fold the waistband along the center wrong side out and overstitch along three edges leaving a 7-10 cm hole into the lower edge. Turn the detail right side out and press it. Make decorative stitch at 0.5 cm from the contour stitching the hole. Set the clasp.